13 PDF Article

repair manual for a similiar Canon printer, the iR, on Ebay for $ to $ and this will tell you how to take apart the printer. I had the same. imageCLASS D – Canon Inc. Canon Imageclass D Service Manual Ebook Canon Imageclass D Service Manual currently available. I have a Canon ImageClass D and repair parts but have no service manual, instructions or diagrams. Canon USA is of No Help on this- they.

Author: Vudobei Dogrel
Country: Liechtenstein
Language: English (Spanish)
Genre: Marketing
Published (Last): 12 April 2015
Pages: 218
PDF File Size: 11.96 Mb
ePub File Size: 19.79 Mb
ISBN: 806-6-72536-162-5
Downloads: 13443
Price: Free* [*Free Regsitration Required]
Uploader: Gardakinos

Chapter 5 Maintenance Periodic Cleaning Your machine requires little periodic maintenance.

imageCLASS D860

Of procedure signals, it is used for actual transmission of image data. If exposed to strong light for a long time, the copies may start to develop white spots or vertical bands. Go to step 7. VRs that must not be used in the field: Using other envelopes may affect the quality of the print image. Can be caused by dirt from imagclass roller.

Canon imageCLASS D860 Basic Manual

NO Close it firmly. If errors do not disappear, try “Long distance 2 ” and “Long distance 3 “. Chapter 13 T Contact sensor drive belt 2 Is the contact sensor drive belt normal? The data of a single page cqnon too large, exceeding the time allowed for reception.

It imageclasa ON when the machine is in energy save mode, and goes OFF when the machine leaves the mode. When SW04 bit 2 is set to ‘1’, the number of final flag sequences will be increased from 1 to 2 for a procedure signal transmitted at bps. The machine will not shift to ESS mode under any of the following conditions: To avoid the condensation, leave the machine unpacked for 1 hr or more so that it will be fully used to the room temperature.


Canon imageCLASS D Service manual |

To prevent overheating, the machine switches among 3 copying speeds with reference to the readings of the sub thermistor. F To mount the control panel, turn it over as shown in 8. You made copies of a letter size document on legal size paper. Press the Set key. T Cassette holding plate spring, Rollers cassette pickup system 7 Sevice the holding plate of the cassette in up position?


T Power cord 2 Is the power cord connected to the machine? Lightly imagsclass any dirt with a dry, soft cloth. If no LTR paper is available, cut a larger sheet of imageclaws so that its width is mm; then, shown in prepare a test sheet, making sure that the width is mm; as for its length, make sure that it fits the copyboard glass.

Modify your browser’s settings to allow Javascript to execute. If no fault is found, try skew removal once again.

T Fixing imagdclass roller 5 Is the surface of the fixing pressure roller normal? The line condition is poor, and the appropriate signal from the other party cannot be received correctly after transmission of MPS.


Note that a dated proof of purchase is required at the time of service. Do not disassemble it. Is the problem corrected?

To select a different transmission speed, use the keypad. Bit 49 of DIS received from the other party is ‘0’. If the face of the light guide assembly becomes soiled or scratched, its optical characteristics will be affected. T Connector 10 Is the connection of the following connectors normal: These bit switches are applicable to manually dialed numbers only.

T Selfoc lens array contact sensor 8 Clean the selfoc lens array of the contact sensor. e860

The Product, when delivered to the original purchaser the “Purchaser” in new condition in the original container, is warranted against defective materials or workmanship, under normal use and service, for a period of three 3 years from iageclass date of purchase as follows: Thick paper H mode; envelope, etc. Does it move smoothly? If the dirt is excessive, use alcohol with lint-free paper thereafter, be sure to dry wipe it with a cloth or lint-free paper.