13 PDF Article

Service Manual, Elna DE Details. Elna Model DE Serger Machine Service Manual, 20 Pages. The physical copy of the instruction manual is a soft cover. Full text of “Elna Serger Instruction Manual dse de e” IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic. Hi there, Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this.

Author: Kezilkree Dagal
Country: Burkina Faso
Language: English (Spanish)
Genre: Career
Published (Last): 22 March 2011
Pages: 337
PDF File Size: 8.8 Mb
ePub File Size: 11.75 Mb
ISBN: 166-1-43972-982-6
Downloads: 12422
Price: Free* [*Free Regsitration Required]
Uploader: Ket

Majual have tightened it from the usual 4 to an 8 and now it seems fine for an inch and then goes bad again. Your answer needs to include more details to help people. Threading the Lower Looper – Coloured green on the chart and on the thread guides.

If it is open, the machine will not work. Remove the needle you are not using the same as for 3-thread use and the upper thread from the machine.

614e First release Model or loosen the tensions, then pull the looper threads gently behind the needle until the knots have passed through. The fabric is not moving it just keeps sewing in the same place.

V Stitch Length Most overlook sewing projects can be done with the stitch length set at 2 to 3. These links may help: You can start overlocking from the edge of the fabric just by feeding it into the front of the lowered presser foot.

  ISSEI YOSHINO SUPER COMPLEX ORIGAMI PDF

Please assign your manual to a product: A Presser Foot Lever To raise the ekna foot, swing the lever c down and you can see the round mark in red, as illustrated.

Elna DE Manuals

It’s worth a thousand words. It is preferable to make a small cut to mark the second stitch line, before starting to sew. Draw the thread back under the presser foot, leaving about 10 cm of thread to the left. However, when the differential feed control slide c is set at 1. Remove the sewing foot see page 5 and the needle plate see page If the fabric tends to pucker, guide it by gently pulling it to the back with your left hand, and at the same time lightly holding it with your right hand, for good stitching results.

Fold the fabric into, a straight edge, as shown, and sew along the edge, trimming very little, if necessary. Pass the thread through the guides A to C.

Right needle thread – Red thread guides 4. When using domestic type spools, remove the cone holders and place the caps b over the spools of mabual.

If you wish to obtain more information, please do not hesitate to contact your dealer who is fully qualified to answer your questions. Re-engage the moving blade see page This helps to prevent sheer and lightweight fabrics from puckering.

  JOE SACHS NICOMACHEAN ETHICS PDF

ELNA 614DE Manuals

With the lower guide line c of the pressure knob at higher level than the top cover surface, lower pressure for very stretchable fabrics is available. How can this be resolved. Raise the needle bar to the highest position. For very stretchable fabrics, loosen it counter-clockwise to decrease the pressure. The tension settings for the 2-thread overcast are different from those of 3- thread use. Oct 29, Elna Sewing Machines. Here’s a link to this great service Good luck!

Pre-set the needle and lower looper thread tension controls at 0. Remember maximum input of the lamp is 15 watts, should it have to be changed. Sep 27, Elna Sewing Machines. Elna Mechanical Sewing Replacing the Moving Blade Replace the moving blade, if it becomes blunt. Have a manual for Elna Sewing Machines?

Bring the lower looper to its right position by turning the flywheel by hand.