Consult International Marine’s INTERTUF DATA SHEET brochure on NauticExpo. Page: 1/4. Intertuf Aluminium. A one pack, tar free vinyl anticorrosive which can be used at temperatures down to -5°C. Packaging: 20L. Documents. Interuf__eng. International Intertuff Vinyl Anticorrosive. A one pack, tar free vinyl anticorrosive which can be used at temperatures down to -5°C (23°F). As an anticorrosive.
|Published (Last):||26 March 2007|
|PDF File Size:||18.32 Mb|
|ePub File Size:||14.30 Mb|
|Price:||Free* [*Free Regsitration Required]|
Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Long term testing is ongoing.
Use in accordance with the standard Worldwide Marine Specifications. Petersburg, Russia, phone: Open the catalog to page 2. IntertufJVA aluminium must be specified as the first coat in an anticorrosive system. Consult your local International Paint representative for specific recommendations.
As application, environmental and design factors can vary significantly, due care should be exercised in the selection, verification of performance and use of the coating. All unused material should be stored in tightly closed containers. All surfaces to be coated should be clean, dry and free from contamination.
All surfaces to be coated should be clean, dry and free from contamination.
INTERNATIONAL INTERTUF ALUMINIUM 20L – Aquafax
Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Vinyl Anticorrosive Airless Spray Conventional Spray This material is a one pack coating and should always be mixed thoroughly with a power agitator before Not recommended.
IntertufJVA aluminium must be specified as the imtertuf coat in an anticorrosive system. Optimum performance is achieved when Intertuf is applied over blasted steel.
Consult your local International Paint representative for specific recommendations. For blasted areas, the primer should be applied before oxidation occurs. Consult your International Paint representative for specific recommendations.
DO NOT thin more than allowed by local environmental legislation. Surface defects revealed by the blast cleaning process, should be ground, filled, or treated in the appropriate manner. Application by brush is recommended for small areas only. Proper ventilation and protective measures must be provided during application and drying to keep solvent vapour concentrations within safe limits and to protect against toxic or oxygen deficient hazards.
As an anticorrosive for both above and below the waterline and also as a sealer coat over Tributyltin TBT antifoulings.
The Online Boating and Maritime Exhibition. Consult your International Paint representative for itnertuf system best suited for the surfaces to be protected. Use International GTA only in exceptional circumstances. DO NOT thin more than allowed by local environmental legislation. Read intertif follow all precautionary notices on the Material Safety Data Sheet and container labels. Subject to reinspection thereafter. Material should be filtered prior to use. Test performance results were obtained in a controlled laboratory environment and International Paint makes no claim that the exhibited published test results, or any other tests, accurately represent results found in all field environments.
Multiple coats may be required to achieve specified film thickness. Technical and application data herein is for the purpose intertuff establishing a general guideline of the coating application procedures.
Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Unmixed material in closed containers should be maintained in protected storage in accordance with information given in the STORAGE Section of this data sheet.
Store in dry, shaded conditions away from sources of heat and ignition. In the event welding interguf flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation.
Recommended Tip Range 0. If oxidation has occurred between blasting and application of Intertufthe surface should be reblasted to the specified visual standard. Related Searches Marine epoxy filler International Marine antifouling International Marine epoxy primer International Marine anti-corrosion primer Zinc primer International Marine merchant ship antifouling International Marine merchant ship primer High-gloss coating International Marine professional vessel antifouling International Marine professional vessel primer International Marine topcoat coating International Marine multi-use antifouling Ballast primer International Marine two-component coating Tin-free antifouling Zinc coating International Marine epoxy coating Acrylic coating International Marine tank coating International Marine coating.
Use International GTA only in exceptional circumstances. Where necessary, remove weld spatter and smooth weld seams and sharp edges. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning.
Application by brush is recommended for small areas only.
INTERTUF DATA SHEET – International Marine – PDF Catalogs | Documentation | Boating Brochures
Multiple coats may be required to achieve specified film thickness. Marine Coatings Marine chemicals Marine lubricants. Use in accordance with the standard Worldwide Marine Specifications. Apply in good weather. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances. Application by roller is recommended for small areas only.